- This topic has 108 replies, 1 voice, and was last updated 17 years, 4 months ago by
.
-
Posts
-
hi any body help to reset
the password for quintum Ax series
gatewasy.
Any one plz mail me .. urgentVamsi,
I tried to provide you specific info to do this, yet this wonderful posting area will not allow certain words (unknown which ones) to be used and I cannot post the exact resolution. You can search through the messages on this topic as it has been discussed many times
Mike
Hello, ?
I need delete a config in my Quintum AX series.
BypassNumberDirAttached[1] : (unspecified)
BypassNumberDirAttached[2] : BypassNumberDirectory-1
BypassNumberDirAttached[3..8]: (unspecified)
PUBHuntLdnDirAttached[1] : HuntLDNDirectory-pub2I need delete the BypassNumberDirAttached[2] : BypassNumberDirectory-1
What is the command for do this I configured but cannt dellete it.can you help me please…
Taisisgüe
In the future, you should download the Command Line reference guide from quintum’s web site under the support section as this should provide you the information needed.
To remove this you need to type
set bnda[2]
Of course you need to be in config mode.
MikeM
mike_voip@hotmail.comThanks So much Mike.
I have the file with the commands CL of Quintum but I cannt found it,
Sorry for spend your time with little problem.
thank you very much.
Have a great day
Regards.i have quin axt2400. my ISP block 1720 port.i want to run it diffrent port like 8022 or 8920.
please help me i want any for quintum ax & other configuration software.my email:syedrepon@yahoo.com
Not sure what you are asking, but if you are looking for software for the quintum units, you should try quintum’s web site first as all the software and documentation available can be found there.
MikeM
mike_voip@hotmail.comDear frens,
I’m using quintum tenor A800. One of my fren disable web configuration. Plz help me to enable remote web configuration.
thanks in advance.
Regards,
PrabeshPrabesh,
If you have an older A800, it is not a case that your friend has disabled it, it is just not available in the older units like A800. You can only configure using telnet.
MikeM
mike_voip@hotmail.comThank you So much Mike.
I’m using Quintum Tenor Multipath switch with serial A002-002F4D/A800. Previously I can able to configure via web interface but nowadays one of my friend disable web configuration or I’m not able to access via internet explorer. Only telnet access work. My friend is out of contact. Now I need to open/close pstn channels and it is easy with web cofiguration. So, Please..please….please help me to enable web configuration or command to open/close channels.
Thanks in advance.
Regards,
Prabesh K.C.
Kathmandu, Nepal.Prabesh,
There are 2 issues here.
1. I believe that due to the size of the latest software, the web interface was completely removed/disabled.
2. Even before that, if you used the web interface in the A800 before and you did not have problems. Consider yourself very lucky as the web interface has not really worked correctly since the beginning.
You should start using and getting used to telnet/cli as this is the only way to really configure the A800.
If you want to disable/enable channels in the pstn port, you do the following from telnet;
config pstn 1
dis 1 x (where x = channel number or a for all)
or
ena 1 x (where x = channel number or a for all)
print (to check your setting)
exit
exit
submitMikeM
mike_voip@hotmail.comHi,
I have Quintum Tenor DX
I have 2 PRI on my Quintum and have 200 DID number..When Somebody calls me dial 123 and extension
Like 123 5511
But when I dial someone to outside they can not see 123 5511 !!!
They see 123 0000 which is my PRI number.How can I configure my quintum to correct this problem…
There is a setting for default ANI in the isdn signaling group. Whatever value you set here will be sent out as the ANI.
MikeM
mike_voip@hotmail.comLet say my phone number is 1155
and my Caller ID send as 1155
I want to add 0392611 prefix before 1155
like 03926111155
- The forum ‘Voice over IP’ is closed to new topics and replies.
