Simple Quintum Tenor configuration

This topic has 3 replies, 1 voice, and was last updated 20 years, 10 months ago by sjosema.

Viewing 4 posts - 1 through 4 (of 4 total)

Author

Posts
18th March 2004 at 10:01 #26688

sjosema
Guest

Hi,

i have Quintum Tenor and I can’t get very simple configuration to work 😉

I have analog line connected to PSTN port and I need quintum to accept
calls from Internet and route it to PSTN lines.

Line connected to PSTN works (tested with quintum “test” command), Quintum
is configured to have public IP and gateway and I set other bunch of other
parameters that I find in documentation…

When I try to connect to Quintum with h323 clients, like ohphone or gnomeeting,
I get messages like “Congested link to remote party” or “Congested link to “Io_address:1720″”

I need Quintum to act just like simple gateway between IP network and PSTN so
that I can put URL like “h323://phone_number@quintum_ip” in
some h323 client and quintum calls local phone number…

If someone could send me a configuration parameters of similar quitum setup it
would be great 🙂

Thanks in advance…
sjosema(at)sezampro(dot)yu

18th March 2004 at 10:03 #26689

sjosema
Guest

>> i have Quintum Tenor

that is “I have Quintum Tenor A 800” 🙂

18th March 2004 at 17:38 #26690

Ivan
Guest

send config
config# print

18th March 2004 at 22:17 #26691

sjosema
Guest

Here it is:
(I changed first two bytes of ip addresses with “xxx.xxx”)

Unit
—-
Unit: 1
IP Address = xxx.xxx.235.199
External IP Address = xxx.xxx.235.199
Internal Network IP Addr 1: 0.0.0.0
Internal Network IP Mask 1: 0.0.0.0
Internal Network IP Addr 2: 0.0.0.0
Internal Network IP Mask 2: 0.0.0.0
Internal Network IP Addr 3: 0.0.0.0
Internal Network IP Mask 3: 0.0.0.0
Name = unit1

Online = 1
Relay ResetTime = 240
Relay Reset Number = 2

TcpKeepAlive = Disabled(0)

System
——
Country Value = 22
Country Code =
Area Code =
Minimum DN = 7
Maximum DN = 20
International Prefix:
Long Distance Prefix =
Carrier Selection Prefix:
Intercom Used = no(0)
Private DN Used = no(0)
Interdigit Timeout = 8 sec.

Contact =
Location =
IP Address : of Snmp Trap Server 1 = 0.0.0.0
IP Address : of Snmp Trap Server 2 = 0.0.0.0
IP Address : of Snmp Trap Server 3 = 0.0.0.0

IP Address : Port # of Syslog Server 1 = 0.0.0.0 : 514
IP Address : Port # of Syslog Server 2 = 0.0.0.0 : 514
IP Address : Port # of Syslog Server 3 = 0.0.0.0 : 514
Syslog Facility = 16

IP Address : Port # of Cdr Server 1 = 0.0.0.0 : 0
IP Address : Port # of Cdr Server 2 = 0.0.0.0 : 0
Cdr Password:
Cdr Format: 0

Ring Frequency = 20 Hz(0)
PSTN Ring Sensitivity = Normal(0)

Primary Time Server: IP Address = 0.0.0.0
Secondary Time Server: IP Address = 0.0.0.0
UTC Offset: Unknown

Disc Tone Frequency: 480 Hz (min) : 620 Hz (max)
Disconnect On/Off Time: 250 mSec(on) : 250 mSec(off)

Call Indication Tone = None(0)
Disable GUI = no(0)

Dialplan
——–
User Programmable DP = No
Dialplan table:
index:Pattern DpType min max nprefix

System LAN
———-
Subnet Mask = 255.255.255.240
Default Gateway = xxx.xxx.235.193

PSTN Trunk Group
—————-
PSTN Trunk Group: 1
Name = PstnPassThrough1
Pass Through = no(0)
PT Trunk ID = 0
Provide Call Progress Tone = no(0)
Busyout = no(0)
Hunt Algorithm = ascending(0)
Modem Calls = No(0)
Direction = both(2)
DN Used = public
End Of Dial = yes(1)
End Of Dial Digit = #
Add End of Dial Digit = no(0)
Ivr Type = None
CID = From Interface(0)
External Routing Request = no(0)
Auto Switch Enable = no(0)
Forced IP Routing # = none
Trunk ID(Account Code) = none
Trunk ID Delivery = none
2 Stage Dial = No
Translate Inbound Caller ID = no(0)
Relay Caller ID = yes(1)
IP Extension = no(0)
Maximum LAM Calls Allowed = 8
LAM: Index Pattern Replacement NumberType
1 < 999> < > 0
Cas Signaling Type = loop start(1)
Cas Orientation = user(0)
Dial Tone Detect = yes(1)
Dial Delay Timeout = 1000
Answer Delay Timeout = 0
Flash-Hook Signaling = no(0)
Supervision = none(0)
Caller Id Detection = no(0)
dtmf-ontime = 100
dtmf-offtime = 100
Channel:
unit# 1 line# 2: 1,2,3,4,5,6,7,8

PBX Trunk Group
—————
PBX Trunk Group: 1
Name = PbxPassThrough1
Pass Through = yes(1)
PT Trunk ID = 0
Provide Call Progress Tone = yes(1)
Multipath = yes(1)
Hunt Algorithm = ascending(0)
Modem Calls = No(0)
Direction = both(2)
DN Used = public
End Of Dial = yes(1)
End Of Dial Digit = #
Add End of Dial Digit = no(0)
Ivr Type = None
Partial TG = no(0)
CID = From Interface(0)
External Routing Request = no(0)
Auto Switch Enable = no(0)
Forced IP Routing # = none
Trunk ID(Account Code) = none
Trunk ID Delivery = none
2 Stage Dial = No
Translate Inbound Caller ID = no(0)
Relay Caller ID = yes(1)
IP Extension = no(0)
Public Number of Digits = 7
Private Number of Digits = 4
Public Hunt Ldn’s:
Private Hunt Ldn’s:
BDN: Index Bdn
Cas Signaling Type = loop start(1)
Cas Orientation = net(2)
Flash-Hook Signaling = yes(1)
Flash-Hook Min = 200
Flash-Hook Max = 700
Supervision = none(0)
Caller Id Generation = no(0)
dtmf-ontime = 100
dtmf-offtime = 100
Channel:
unit# 1 line# 1: 1,2,3,4,5,6,7,8

IP Trunk Group
—————
Incoming IP call delete digits = 0
Incoming IP call prefix =
Outgoing IP call delete digits = 0
Outgoing IP call prefix =
Prefix Trunk ID = no(0)
Default Trunk = No
External Routing Request = no(0)
Display Information ID = Tenor-Gateway

Line
—-
Line: 1
Law = uLaw(0)
Rx Gain = -4dB
Tx Gain = -2dB
Line: 2
Law = uLaw(0)
Rx Gain = 0dB
Tx Gain = 0dB
Guard Time = 0mS
DAA Start Up = Enabled

Bandwidth Management
——————–
Time of Day Maximum Bandwidth:
Day = 0(Sunday)
Hour = 00 1536000 1536000 1536000 1536000 1536000 1536000
Hour = 06 1536000 1536000 1536000 1536000 1536000 1536000
Hour = 12 1536000 1536000 1536000 1536000 1536000 1536000
Hour = 18 1536000 1536000 1536000 1536000 1536000 1536000
Day = 1(Monday)
Hour = 00 1536000 1536000 1536000 1536000 1536000 1536000
Hour = 06 1536000 1536000 1536000 384000 384000 384000
Hour = 12 384000 384000 384000 384000 384000 384000
Hour = 18 1536000 1536000 1536000 1536000 1536000 1536000
Day = 2(Tuesday)
Hour = 00 1536000 1536000 1536000 1536000 1536000 1536000
Hour = 06 1536000 1536000 1536000 384000 384000 384000
Hour = 12 384000 384000 384000 384000 384000 384000
Hour = 18 1536000 1536000 1536000 1536000 1536000 1536000
Day = 3(Wednesday)
Hour = 00 1536000 1536000 1536000 1536000 1536000 1536000
Hour = 06 1536000 1536000 1536000 384000 384000 384000
Hour = 12 384000 384000 384000 384000 384000 384000
Hour = 18 1536000 1536000 1536000 1536000 1536000 1536000
Day = 4(Thursday)
Hour = 00 1536000 1536000 1536000 1536000 1536000 1536000
Hour = 06 1536000 1536000 1536000 384000 384000 384000
Hour = 12 384000 384000 384000 384000 384000 384000
Hour = 18 1536000 1536000 1536000 1536000 1536000 1536000
Day = 5(Friday)
Hour = 00 1536000 1536000 1536000 1536000 1536000 1536000
Hour = 06 1536000 1536000 1536000 384000 384000 384000
Hour = 12 384000 384000 384000 384000 384000 384000
Hour = 18 1536000 1536000 1536000 1536000 1536000 1536000
Day = 6(Saturday)
Hour = 00 1536000 1536000 1536000 1536000 1536000 1536000
Hour = 06 1536000 1536000 1536000 1536000 1536000 1536000
Hour = 12 1536000 1536000 1536000 1536000 1536000 1536000
Hour = 18 1536000 1536000 1536000 1536000 1536000 1536000

Gatekeeper Administration
————————-

Endpoint Authorization Type = 3 (Term+Orig)

Allowed Endpoints
IP Mask
1 xxx.xxx.235.199 255.255.255.0
2 xxx.xxx.62.252 255.255.255.255

Barred Endpoints
IP Mask
No Barred Endpoints Configured

Gatekeeper System
—————–
Zone Name =
Border Element IP Address(prim) = 0.0.0.0
Border Element IP Address(sec) = 0.0.0.0
Discovery IP Address = 0.0.0.0
Gatekeeper Password =
LRQ returns all candidates(0)
Maximum LRQ Hops = 0
WAN Call Limit = 0 (disabled)
LCF/LRJ V3plus = 1
Gatekeeper Option Flags:
Use IP Header Address = no(0)
Ridgeway ARQ = no(0)

Border Element
—————–
Static Routing
No Static Routes configured

DSP
—
Voice Coding algorithm = 81
Voice Information Field size = 192 bits
Silence Suppression = Enable(1)
Minimum Jitter buffer = 60 msec
Maximum Jitter buffer = 300 msec
Receive Gain (PCM -> IP) = -2 dB
Transmit Gain (IP -> PCM) = -4 dB
Digit Relay = 0
Fax Relay Type = 0
Fax Maximum Rate = 144
Fax Playout FIFO nominal delay = 600
Fax Modem Coding = 0
Idle Time = 0
Answer Supervision Options = 0

AutoSwitch
———-
Auto Threshold = 50

H323 Gateway
—————–
Primary GK Address = 0.0.0.0
Primary Auto Discovery = 0
Secondary GK Address = 0.0.0.0
Secondary Auto Discovery = 0
H.323 ID =
Register DN = Register as GW Prefixes(1)
Ignore Bandwidth in ACF = no(0)
Default H245 Tunneling = yes(1)
Round Trip Delay = 0
One Stage Dialing = 0
RRQ Interval = 0
H323 Interop Flags:
H225 GW Protocol = h323(0)
Do BRQ = 0
SlaveSessionId0 = 0
AllowFastStartOnly = No(0)
RRQv3plus= No(0)
ProgressInd Alert= No(0)
StartH245Flag= No(0)
Automatic Ext IP Update= No(0)
RTP Verification= No(0)

Do Lightweight RRQ = no(0)

Radius User
———–

host p 0.0.0.0
authenticationport p 1812
accountingport p 1813

host s 0.0.0.0
authenticationport s 1812
accountingport s 1813

retry = 3
timeout = 5
accountingtype = 0
billingvendor 0
sharedsecret

IVR
——

Primary File Server: IP Address = 0.0.0.0
Secondary File Server: IP Address = 0.0.0.0
timeout: 0

Enabled Languages: None

CID Translation Table
——
Caller ID Translation Table
Index Pattern Replacement

Radius Endpoint
—————

host p 0.0.0.0
authenticationport p 1812
accountingport p 1813

host s 0.0.0.0
authenticationport s 1812
accountingport s 1813

retry = 3
timeout = 5
idtype = 0
passwordtype = 0
sharedsecret

Product Name: Tenor Analog A800 Multipath Switch – 8 ports (Rev. B)
Gatekeeper Status: Mini
GK Calls Allowed: 8
Feature Bit Status: -PS/+RB/-ER
Languages allowed: 1
Serial Number: A002-00281E
Ethernet Address: 00-30-E1-00-28-1E
IP Address: xxx.xxx.235.199
Subnet Mask: 255.255.255.240
Default Gateway: xxx.xxx.235.193
System Software Version: P4-2-20-28(LEC) (1720084/0x6856)
Boot Software Version: P4-1-3 (180592/0xE814)
Database Version: 2.08 09-13-2000 (277900)
Author

Posts

Viewing 4 posts - 1 through 4 (of 4 total)

The forum ‘Voice over IP’ is closed to new topics and replies.

Simple Quintum Tenor configuration

More info

More info