[Noname]

There are the same number of phisical ports on the A400 and A800.

On the A400, they are single ports, with only one phone line per plug.

On the A800, each plug have two phone lines . One is carried out on the green/red wires, the second line is carried out on the yellow/black pair.

Take the line that come out from the Quintum to a Rj-11 block. Connect via wires to two diferent phone lines that way.

Or buy one of those plastic splitters on any electronic stores that open up the lines in two diferent circuits.

[Chidi]

My Quintum A800 RJ-11 supplied connectors have on one end:single connector and on the other end two connectors labelled ‘A’ and ‘B’. Where do these connect to? Does the PBX connection differ from the PSTN connection? Please help.

[Saul Bejarano]

Configuration of a Quintum D2400 with voicemaster for IVR.
For questions contact saul@procomm100.com
http://www.procomm100.com

print

Unit
—-
Unit: 1
IP Address = 65.33.45.234
External IP Address = 0.0.0.0
Name = gw.01.usa
Clock Source = PSTN(0)

Online = 1
Relay ResetTime = 240
Relay Reset Number = 2

TcpKeepAlive = Disabled(0)

System
——
Country Value = 0
Country Code = 1
Area Code = 239
Minimum DN = 7
Maximum DN = 18
International Prefix:
Long Distance Prefix =
Carrier Selection Prefix:
1: 101xxxx
US 10 Digit Dial Plan = no(0)
Intercom Used = no(0)
Private DN Used = no(0)
Interdigit Timeout = 4 sec.

Contact = roger_bruun
Location = naples-florida
IP Address : of Snmp Trap Server 1 = 66.250.220.60
IP Address : of Snmp Trap Server 2 = 0.0.0.0
IP Address : of Snmp Trap Server 3 = 0.0.0.0

IP Address : Port # of Syslog Server 1 = 66.250.220.60 : 514
IP Address : Port # of Syslog Server 2 = 0.0.0.0 : 514
IP Address : Port # of Syslog Server 3 = 0.0.0.0 : 514
Syslog Facility = 16

IP Address : Port # of Cdr Server 1 = 0.0.0.0 : 0
IP Address : Port # of Cdr Server 2 = 0.0.0.0 : 0
Cdr Password:
Cdr Format: 0

Primary Time Server: IP Address = 128.227.205.3
Secondary Time Server: IP Address = 216.133.140.77
UTC Offset: – 05:00

Disc Tone Frequency: 0 Hz (min) : 0 Hz (max)
Disconnect On/Off Time: 0 mSec(on) : 0 mSec(off)

Call Indication Tone = None(0)
Disable GUI = no(0)

Dialplan
——–
User Programmable DP = No
Dialplan table:
index:Pattern DpType min max nprefix

System LAN
———-
Subnet Mask = 255.255.255.0
Default Gateway = 65.33.45.1

PSTN Trunk Group
—————-
PSTN Trunk Group: 1
Name = ICE_PSTN
Pass Through = no(0)
PT Trunk ID = 100
Provide Call Progress Tone = yes(1)
Busyout = no(0)
Hunt Algorithm = ascending-round-robin(2)
Overlap Dial = no(0)
Modem Calls = No(0)
Direction = both(2)
DN Used = public
End Of Dial = no(0)
Ivr Type = Prepaid calling card
Ivr Card Digit Length = Variables
Disabled Voice Prompt 0
Ivr Language Type = 0
Ivr Language = None
MultiSession code: = None
IVR Access Number = None
Ivr Answer Delay = 4
Retry Counter = 1
CID = From Interface(0)
External Routing Request = no(0)
Auto Switch Enable = no(0)
Forced IP Routing # = none
Trunk ID(Account Code) = none
Trunk ID Delivery = none
2 Stage Dial = No
Translate Inbound Caller ID = no(0)
Relay Caller ID = no(0)
IP Extension = no(0)
Maximum LAM Calls Allowed = 24
LAM: Index Pattern Replacement NumberType TON NPI
CCS Or CAS = ccs(0)
Channel:
unit# 1 line# 2: 1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24

PBX Trunk Group
—————

IP Trunk Group
—————
Incoming IP call delete digits = 0
Incoming IP call prefix =
Outgoing IP call delete digits = 0
Outgoing IP call prefix =
Prefix Trunk ID = no(0)
Default Trunk = No
External Routing Request = no(0)
Display Information ID =

Line
—-
Line: 1
Law = uLaw(0)
T1 or E1 = T1(0)
Line Code = B8ZS(0)
CRC = yes(1)
T1 Framing Format = ESF(1)
T1 Long or Short = short haul(0)
T1 Length = 133ft(0)
Line: 2
Law = uLaw(0)
T1 or E1 = T1(0)
Line Code = B8ZS(0)
CRC = yes(1)
T1 Framing Format = ESF(1)
T1 Long or Short = short haul(0)
T1 Length = 133ft(0)

Signaling
———
Signaling Group: 2
Name = cc1
ISDN Protocol Type = NI2(3)
Orientation = user/slave(0)
DCh Num = 24
Ignore TON/NPI = yes
FAS unit = 1
FAS line = 2
link establishment = always(1)
Relay PROG = yes(1)
Force Outbound BCAP = No(0)
Forced ProgInd IE Outbound = Disabled

Bandwidth Management
——————–
Time of Day Maximum Bandwidth:
Day = 0(Sunday)
Hour = 00 * * * * * *
Hour = 06 * * * * * *
Hour = 12 * * * * * *
Hour = 18 * * * * * *
Day = 1(Monday)
Hour = 00 * * * * * *
Hour = 06 * * * * * *
Hour = 12 * * * * * *
Hour = 18 * * * * * *
Day = 2(Tuesday)
Hour = 00 * * * * * *
Hour = 06 * * * * * *
Hour = 12 * * * * * *
Hour = 18 * * * * * *
Day = 3(Wednesday)
Hour = 00 * * * * * *
Hour = 06 * * * * * *
Hour = 12 * * * * * *
Hour = 18 * * * * * *
Day = 4(Thursday)
Hour = 00 * * * * * *
Hour = 06 * * * * * *
Hour = 12 * * * * * *
Hour = 18 * * * * * *
Day = 5(Friday)
Hour = 00 * * * * * *
Hour = 06 * * * * * *
Hour = 12 * * * * * *
Hour = 18 * * * * * *
Day = 6(Saturday)
Hour = 00 * * * * * *
Hour = 06 * * * * * *
Hour = 12 * * * * * *
Hour = 18 * * * * * *

Gatekeeper Administration
————————-

Endpoint Authorization Type = 0 (None)

Allowed Endpoints
IP Mask
No Allowed Endpoints Configured

Barred Endpoints
IP Mask
No Barred Endpoints Configured

Gatekeeper System
—————–
Zone Name = naples
Border Element IP Address(prim) = 65.33.45.234
Border Element IP Address(sec) = 0.0.0.0
Discovery IP Address = 65.10.2.209
Gatekeeper Password =
LRQ returns all candidates(0)
Maximum LRQ Hops = 0
WAN Call Limit = 0 (disabled)
LCF/LRJ V3plus = 0
Gatekeeper Option Flags:
Use IP Header Address = no(0)
Ridgeway ARQ = no(0)

Border Element
—————–
Static Routing
No Static Routes configured

DSP
—
Voice Coding algorithm = 68
Voice Information Field size = 160 bits
Silence Suppression = Enable(1)
Minimum Jitter buffer = 60 msec
Maximum Jitter buffer = 300 msec
Receive Gain (PCM -> IP) = -2 dB
Transmit Gain (IP -> PCM) = -4 dB
Digit Relay = 1
Fax Relay Type = 0
Fax Maximum Rate = 144
Fax Playout FIFO nominal delay = 600
Fax Modem Coding = 0
Idle Time = 0
Answer Supervision Options = 2

AutoSwitch
———-
Auto Threshold = 50

H323 Gateway
—————–
Primary GK Address = 66.10.2.209
Primary Auto Discovery = 1
Secondary GK Address = 0.0.0.0
Secondary Auto Discovery = 0
H.323 ID = naples01.gw.usa
Register DN = No(0)
Ignore Bandwidth in ACF = yes(1)
Default H245 Tunneling = yes(1)
Round Trip Delay = 0
One Stage Dialing = 0
RRQ Interval = 180
H323 Interop Flags:
H225 GW Protocol = h323(0)
Do BRQ = 0
SlaveSessionId0 = 0
AllowFastStartOnly = Yes(1)
RRQv3plus= No(0)
ProgressInd Alert= No(0)
StartH245Flag= No(0)
Automatic Ext IP Update= No(0)
RTP Verification= No(0)

Do Lightweight RRQ = yes(1)

Radius User
———–

host p 66.10.2.209
authenticationport p 1812
accountingport p 1813

host s 0.0.0.0
authenticationport s 1812
accountingport s 1813

retry = 5
timeout = 10
accountingtype = 2
billingvendor 1
sharedsecret *******

IVR
——

Primary File Server: IP Address = 66.10.2.209
Secondary File Server: IP Address = 0.0.0.0
timeout: 10

Enabled Languages: 0

CID Translation Table
——
Caller ID Translation Table
Index Pattern Replacement

Radius Endpoint
—————

host p 0.0.0.0
authenticationport p 1812
accountingport p 1813

host s 0.0.0.0
authenticationport s 1812
accountingport s 1813

retry = 3
timeout = 5
idtype = 0
passwordtype = 0
sharedsecret

Product Name: Tenor Digital Multipath Switch – 24 ports (Rev. B)
Gatekeeper Status: Mini
GK Calls Allowed: 16
Feature Bit Status: -PS/+RB/-ER
Languages allowed: 1
Serial Number: A001-000B2E
Ethernet Address: 00-30-E1-00-0B-2E
IP Address: 65.40.42.209
Subnet Mask: 255.255.255.128
Default Gateway: 65.40.42.129
System Software Version: P4-2-20-20(LEC) (1830074/0xD44E)
Boot Software Version: P4-1-3 (180590/0xA9E6)
Database Version: 2.08 09-13-2000 (277900)

[kumar]

I had a few question about a tenor A800 .with tenor iam using cellsocket what is the confg please help me .

Thanks and hope you can help me.

[Imran]

Kumar, We are using cellsocket with quintum a400, so the same settings would be for tenor 800, the cellsocket gives voltage of only 24v against the required 48v to the tenor ports, so the voltage has to be adjusted in the tenor, ask your service provider to change that setting in the tenor

[KUMAR]

Hi Imran,

CAN U HELP ME OUT IN THIS HOW TO CONFIG THE A800 TO ADJUST THE VOLTAGE .

THANKS
KUMAR

[imran]

kumar, send me in your config and i will check with mine and let you know what to change, the change was done by my service provider, so i need to cross check, email me at info@dial2globe.com
imran

[Sandeep]

Hello Friend,

I have two Tenor A400. i want to setup two location . but i have one side 8 Real Ip . and another i dont have real ip . Plz Email me both unit work or not . and how to setup unit. plz email me

[BAHMAN]

HI DEAR MANAGER ,
I HAVE THE VOIP STATION WITH 10 UNIT OF TENOR A800 , I CAN USE WITH RADIUS FILES , BUT I NEED TO USE WITH CDR FILES BECASE THE CDR FILES MORE COMPLETE INFORMATION THAN RADIUS FILES .
I CONFIGURED ON TENOR ( CDRSERVERIP , CDRSERVERPORT ( 9002 OR 9003 ) , CDRPASSWORD ) BUT I DONT KNOW IN MY COMPUTER SERVER WHICE SECTION OF WINDOWS COMPONENT MUST BE CONFIGURE FOR RECIVING THE CDR FILES FROM TENOR . PSL HELP ME IF YOU CAN.
THANKS AND BEST REGARDS
BAHMAN BANIADAM
DORSA COMPUTER
MAILTO : bahman_baniadam@hotmail.com

[okechi]

pls i want setup ivr server to work with my tenor A800.Thus could any one help recommend a cheaper software(voice software) to use for the ivr ( i want to start a prepaid calling card system)

OKECHI

[reza]

hello,
when i enter GateWay IP for tenor A800 it does not work . it is falling to a loop of reset and password command prompt doesn’t come. and when i clean the gateway and put that 0.0.0.0 it will work correct. what must I do? plz email me. thank u

[cypherdecode]

I have a Quintum A800, ASR is low because of too many “Cause Code 16” (Normal Call Clearing). The manual says “The cause indicates that the call is being cleared because one of the user has requested that the call be cleared.”

Anybody knows what’s causing this code to occur?

[www.blue-lava.co.uk]

Hi Reza,

It is a common set up problem on Quintum that when you enter the IP information the machine then goes into a loop of rebooting.

This is because the subnet and the IP number you have chosen do not match up – this is often due to mis-keying the information (I know, I’ve done it myself more than once!).

To rectify the problem boot the Quintum with a console cable plugged in the front – then press [RETURN] when prompted. You will then be able to reset the parameters.

Hope this helps, if you need any further assistance please feel free to contact me at: mhitchcock@blue-lava.co.uk

Thanks,

Mat

[nima]

hi

I have a problrm with quintum tenor stared at 3 day ago

after a few minute tenor was reset automaticly and tenor`s alarm LED started blink and we reccived this errors
217.66.217.161:1:rpt:1:critical softwear Error (VManagerProc(l7): failed to crate translator):0:0

—–
and finaly report this error

tenor is in bypass mode

at this time we must reset tenor manualy
———-

please help me
tnx

[reza]

dear mat; hi
thank u
but it seems IP and GateWay are working correctly and dosenot have any problem. because the PC that is pluged to the this IP and GateWay works without any problem.
is there any command in tenor’s config that may be related with this problem?
thank u again

[Author]

Posts