- This topic has 177 replies, 1 voice, and was last updated 17 years, 4 months ago by
.
-
Posts
-
How to config 2nd dail on tenor A400?
I only config IVRTYPE = 1, but I dail into A400, may hear a 2nd dail tone ,and I dail destination’s number ,but no response ,log file shows bad format number
can yuu help me ,give me a sample configuration?
Telnet into the unit and log in. Once you get the prompt, type gk and enter.
At the gatekeeper prompt,type gk route and the number that you are dialing.
For example if you are calling to Argentina you will type 01154 plus the area code and the number.
The A400 will answer witha list of the gateways that could take your call at that moment.
If it returns a “no candidates”. the number that you are dialing is not right.
You could also see who is registered on your unit by typing
gk ep return
That will give you a list of all the numbers reacheable from your a400.
Give a holler if you need more help.
Remove the first part nobswboyrie@yahoo.com
Start with the “w”Good luck!!!!!
thanks ,I can see the number that I dialed in gk table.
if i dial from tenor A400 to another tenor A400 is right ,I guess that the route is right.so I can’t find out the problem .
the log
Quintum:beijing e +ch cas ivr
e +ch cas ivr
Event Log Add To Mask…
Enabled Modules: excp ch cas ivr
Quintum:beijingQuintum:beijing
Quintum:beijing
Quintum:beijing
Quintum:beijing e
e
Dumping Event Log…
Product Name: Tenor Analog A400 Multipath Switch – 4 ports (Rev. B)
Gatekeeper Status: Mini
GK Calls Allowed: 4
Feature Bit Status: -PS/+RB
Languages allowed: 1
Serial Number: A002-001A27
Ethernet Address: 00-30-E1-00-1A-27
IP Address: 192.168.0.20
Subnet Mask: 255.255.255.0
Default Gateway: 0.0.0.0
System Software Version: P4-2-7+(Raj-11/7/2002)(LEC) (1774551/0x0F16)
Boot Software Version: P4-1-3 (180592/0xE814)
Database Version: 2.08 09-13-2000 (267200)
Time (since last reset): 2719 secondsCAS : 266576:Received Message
CAS : 266576:mtype = 64
CAS : 266576:CAS: HL Message
CAS : 266576:CAS: ABCHANGE Message
CAS : 266576:Process AB change: [2,1] ABCD=0x0.
CAS : 266576:[2,1] Set Disc States
CAS : 266576:LocalDiscState = 0
CAS : 266576:RemoteDiscState = 0
CAS : 266576:HL Event = 11
CAS : 266576:[2,1] casProc: Idle-Seizure
CAS : 266576:Sent Msg to Usid = 44
CAS : 266576:[2,1] Sent SETUP to CH
CAS : 266576:[2,1] New State = 6
CH : 266576:[2: 1] received message from cas: Setup
CH : 266576:CallInfo[0xd7f428]: origCalled.digit()
.
CH : 266576:[2: 1] sent message to cas: Call-Proc
CAS : 266576:Received Message
CAS : 266576:mtype = 128
CAS : 266576:CAS: ISDN Message
CAS : 266576:Process ISDN Message [2,1]: imsg=3.
CAS : 266576:In decode: message code = 3
CAS : 266576:[2,1] Decode CALLPROC
CAS : 266576:[2,1] casProc: i3-CALLPROC
CAS : 266576:Sent Msg to Usid = 44
CAS : 266576:[2,1] Sent INBANDSIGDONE to CH
CAS : 266576:[2,1] New State = 6
CH : 266576:OBCSM[20]: pin: .
CH : 266576:Routing requested for: public(1) orig=1 public(0) normalized=1111* route code= .
CH : 266576:1 match(es) found: 0
CH : 266576:IVR(0xd7dc04): Instantiating new IVR.
CH : 266576:IVR(0xd7dc04): peerRcvSetup
CH : 266576:IVR[0xd7dc04]: pin: 1.
CH : 266576:IVR Type=1 PIN=
CH : 266576:[2: 1] sent message to cas: Alert
CH : 266576:OBCSM[20]: Received peerRcvConnect.
CH : 266576:[2: 1] sent message to cas: Connect
CH : 266576:[2: 1] received message from cas: InbandSigDone
CH : 266576:tsi connect: 001 208 01
CH : 266576:TsiConnXlate: 0:1, 2:8
CH : 266576:tsi connect: 001 208 10
CH : 266576:TsiConnXlate: 2:8, 0:1
CAS : 266576:Received Message
CAS : 266576:mtype = 128
CAS : 266576:CAS: ISDN Message
CAS : 266576:Process ISDN Message [2,1]: imsg=4.
CAS : 266576:In decode: message code = 4
CAS : 266576:[2,1] casProc: i3-ALERTING
CAS : 266576:[2,1] New State = 6
CAS : 266576:Received Message
CAS : 266576:mtype = 128
CAS : 266576:CAS: ISDN Message
CAS : 266576:Process ISDN Message [2,1]: imsg=5.
CAS : 266576:In decode: message code = 5
CAS : 266576:[2,1] Decode CONNECT
CAS : 266576:[2,1] casProc: i3-CONNECT
CAS : 266576:[2,1] Set Disc States
CAS : 266576:LocalDiscState = 1
CAS : 266576:RemoteDiscState = 0
CAS : 266576:[2,1] Send Answer to Line
CAS : 266576:[2,1] Send ABCD = 15
CAS : 266576:[2,1] New State = 7
CAS : 266584:Received Message
CAS : 266584:mtype = 64
CAS : 266584:CAS: HL Message
CAS : 266584:CAS: ABCHANGE Message
CAS : 266584:Process AB change: [2,1] ABCD=0x5.
CAS : 266584:HL Event = 7
CAS : 266584:[2,1] casProc: Disc-Idle for incoming call
CAS : 266584:ixDiscIdle: ignoring ring-off/idle ab-change
CAS : 266584:[2,1] New State = 7
CH : 266676:IVR(0xd7dc04): ProcessTimerExpiration. State=1
CH : 268676:IVR[0xd7dc04]: Bad number format dialled: .
CH : 268676:IVR(0xd7dc04): Aborting IVR.
CH : 268676:tsi disconnect: 208 001 01
CH : 268676:TsiDiscXlate: 2:8, 0:1
CH : 268676:tsi disconnect: 208 001 10
CH : 268676:TsiDiscXlate: 0:1, 2:8
CH : 268676:OBCSM[20]: Release from peer=0xd7dc04 cause=0x1c redir=.
CH : 268676:CallInfo[0xd7f428]: cdr callid(14) rmtcallid(0) calltype(1) destnumtype(0).
CH : 268676:CallInfo[0xd7f428]: cdr dest(1111*) orig() remote() pin().
CH : 268676:CallInfo[0xd7f428]: cdr icline(1) icport(0) otline(ff) otport(405465).
CH : 268676:CdrManager::addCdr: 19 Return.
CH : 268676:CallInfo[0xd7f428]: sendDisconnected Event.
CH : 268676:tsi connect: 001 201 10
CH : 268676:TsiConnXlate: 2:1, 0:1
CH : 268676:CallInfo[0xd7f428]: sendDisconnected Event.
CH : 268676:[2: 1] sent message to cas: Alert
CAS : 268676:Received Message
CAS : 268676:mtype = 128
CAS : 268676:CAS: ISDN Message
CAS : 268676:Process ISDN Message [2,1]: imsg=4.
CAS : 268676:In decode: message code = 4
CAS : 268676:[2,1] New State = 7
CH : 270476:OBCSM[20]: Disconnecting tone (previously connected).
CH : 270476:OBCSM[28]: cause = 10489532
.
CH : 270476:tsi disconnect: 001 201 10
CH : 270476:TsiDiscXlate: 2:1, 0:1
CH : 270476:[2: 1] sent message to cas: Disc
CAS : 270476:Received Message
CAS : 270476:mtype = 128
CAS : 270476:CAS: ISDN Message
CAS : 270476:Process ISDN Message [2,1]: imsg=6.
CAS : 270476:In decode: message code = 6
CAS : 270476:[2,1] Decode DISC
CAS : 270476:[2,1] casProc: DISC for incoming call
CAS : 270476:[2,1] casProc: Disc Proc
CAS : 270476:discProc: local disc state = 1
CAS : 270476:discProc: remote disc state = 0
CAS : 270476:[2,1] Send Disc-Idle to Line
CAS : 270476:[2,1] Send ABCD = 5
CAS : 270476:LocalDiscState = 0
CAS : 270476:[2,1] Start Delay, ID = 8
CAS : 270476:[2,1] New State = 10
CAS : 270581:Delay Event = 8
CAS : 270581:Stopped Delay D = 8
CAS : 270581:[2,1] casProc: x5x-D8
CAS : 270581:Sent Msg to Usid = 44
CAS : 270581:[2,1] Sent RELCOMP to CH
CAS : 270581:[2,1] New State = 0
CH : 270581:[2: 1] received message from cas: RelCompPLZ help me for ip address config in tenor A800
TX
To enter a new I.P. address for the tenor:
Login into the machine
From the prompt type “config”
Now the prompt is “config#”
Type “unit 1”
Prompt is now “config unit 1#”
type Ip zzz.222.sss.ddd.After you do enter the I.P.adress, you need to type “submit” for the terminal to keep the setting.
The changes will not be efective until you reset or reboot the unit.You could use the “reset” command to do that.
If you have a e-mail that could hold around 2.8 mb, I could send you the whole quintum tenor manual.
No one working in a tenor should be without it.
be sure that you could receive around 3mb file.
Post your e-mail address and I will send it to you.Quiensabe: could you please send me tenor manual?
Quiensabe,
Hi. I wonder if you can do me a favor. Can i have a complete copy of your quintum manual? I. currently setting up quintum d3000 and having a hard time in configuring it. I really much appreciated if you can email it to: jdmjamboo@hotmail.com and/or jdmjamboo@yahoo.com.
Manual was sent to your address
If anyone else need a copy of the CLI manual (soft) write me a mike3799@yahoo, and I will send you the file.
The file is large. Be sure that there is room on your e-mail acccount.
Good luck!!!!!
Quiensabe: could you please send me tenor manual?
in the event log there is a referance number beside each event,
is there any way to query this event deeper ??Hello, You can set the level of the event log. Email me for specifics. Mattg@telcomproducts.com
I want to make simple conection between two tenor having single phone at both side.
I have made sroute & what else configuration has to implement.
If you need to call from a single line phone to a single line phone, it is very simple.
You need to asign a phone number to the ports where the phonew is attached to .
Lets say site “A” have a phone on port one. All what you need to do is assign a number (real or other) to the port. That becames the phone number to that port.
It is simpler to keep the internation format, since Quintum route calls following that format.Lets say that location “A” is in New York. You tell the Quintum that:
1) Country code is 1
2) Area code is 212
3) Port 1 is 555-1212
4) Port 2 is 555-1213When a call arrives ,via voip that have the number 1 212 5551212, the quintum will look up on the table and route it to port 1.
If you need a sample configuration,email me mike3799@yahoo and I could send you a sample for a A400.
Regards!!!!
Hello , i have a quintum a400 tenor (analog series).. also ivr and radius server.. when call ended from both side (my tenor and destination number) quintum’s led turn off after one minute later.In pstntg prompt i’ve configured cassignaling to 1 and supervision 3.. Then same problem occured. And then i’ve changed casssignaling to 6 (loop fast and disconnect) and supervision 3 same problem occured too.. There is no wrong charge…Radius calculates the true calling time.. How can i solve this problem?
- The forum ‘Voice over IP’ is closed to new topics and replies.
