Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Call drop in 3G -UMTS

Viewing 15 posts - 16 through 30 (of 36 total)
1 2 3
  • Author
    Posts
  • 12th April 2017 at 12:42 #57266
    pix
    Guest

    hi Nios

    To reduce or increase the coverage of a cell, you may (primarily) tune the CPICH power :
    primaryCpichPower
    Amos: get utranCell primaryCpichPower
    By default, use 330 (ie. 33dBm)
    Dependencies: primaryCpichPower less than maximumTransmissionPower

    Decreasing the cpich will reduce the cell coverage, but also decrease the Ec/No of the users inside the cell. They will “hear” more interferences.

    A good way to check the coverage distance of a cell is to extract the counter “pmPropagationDelay”, at RBS level (class prach)
    Amos : pmx prach pmPropagationDelay -m 3 -a
    Within one sector, only analyse cells with highest amount of samples (ie. where the UE are camping).

    Regards,
    pix

    14th June 2017 at 04:22 #57267
    Parsa48
    Guest

    I have a lot of cs drop calls in Ericsson baseband 5216 for u900 technology please help me

    17th June 2017 at 20:18 #57268
    pix
    Guest

    hi,

    Many call drops in U900 is usually caused by users getting too low coverage of u900, without possibility of handover to another cell.

    check the neighbour relation with GSM cells, check the event 2d thresholds, the 3a threshold.

    Also check 3G neighbours…

    but really, the first step would be to investigate the kpis and the topology, and understand what is causing the drops.

    Cheers
    pix

    18th June 2017 at 11:28 #57269
    Pawan Sharma
    Guest

    Hi,

    as per the Huawei please check the given switch for CDR improvement.
    OptimizationSwitch(BSC6900,BSC6910): SRB_RESET_RL_SETUP_SWITCH
    OptimizationSwitch(BSC6900,BSC6910): MC_RL_RESET_SWITCH
    PROCESSSWITCH4(BSC6910,BSC6900): RB_SETUP_RL_REEST_SWITCH
    PROCESSSWITCH4(BSC6910,BSC6900): RB_SETUP_ENHANCE_RL_REEST_SWITCH
    OptimizationSwitch(BSC6900,BSC6910): ASU_RL_RESET_SWITCH
    OptimizationSwitch(BSC6900,BSC6910): RB_RECFG_RL_REEST_SWITCH
    PROCESSSWITCH4(BSC6910,BSC6900): RBRECFG_ENH_RL_REEST_SWITCH
    ImprovementSwitch(BSC6900,BSC6910): NON_DCCC_RBRECFG_RL_REEST_SWITCH
    PROCESSSWITCH4(BSC6910,BSC6900): TRB_RESET_RL_REEST_SWITCH
    PROCESSSWITCH4(BSC6910,BSC6900): RB_REL_RL_REEST_SWITCH
    PROCESSSWITCH4(BSC6910,BSC6900): PHY_RECFG_REEST_SWITCH
    PROCESSSWITCH4(BSC6910,BSC6900): PHYCHRECFG_ENH_RL_REEST_SWITCH
    OptimizationSwitch(BSC6900,BSC6910): CS_RL_SETUP_SWITCH
    OptimizationSwitch(BSC6900,BSC6910): PS_RL_SETUP_SWITCH
    OptimizationSwitch4(BSC6900,BSC6910): RB_RLREEST_AM_TRB_RLC_REEST_SWITCH
    OptimizationSwitch4(BSC6900,BSC6910): RB_SETUP_UM_TRB_RLREEST_ADJUD_OPT_SWITCH

    2nd August 2017 at 02:39 #57270
    Parsa48
    Guest

    I am working in Ericsson 3g and 4g networks. There’s a problem in 3G network(u900 with baseband 5216) .the uplink quality is very bad and in road area the subscribe could not use 3g data and in most times they have edge. Please guide me to know the reason and how to solve the problem

    5th August 2017 at 13:08 #57271
    LEMAURE
    Guest

    Dear PARSA
    make sure the neighboring GSM cells are well refarmed. Did you perform SSV on those sites?

    9th August 2017 at 11:20 #57272
    hungryforknowledge247
    Guest

    Hi Parsa48,
    Poor uplink quality on U900 could be due to many reasons.
    Have you checked dominance in the area.
    Is it just one site or cluster of sites.
    Check for Scrambling code clashes.
    Get it drive tested and analyse log files.
    Check if there is external interference.
    What is the value of Prx Noise you are getting.
    Check 3G-2G and 3G-3G neighbours.

    13th August 2017 at 02:08 #57273
    Parsa48
    Guest

    Hi to all dear
    What is the fast dormancy feature?
    How can iI check and adjust in Ericsson ran?

    13th August 2017 at 02:21 #57274
    Parsa48
    Guest

    Kindly anyone help me for increasing wcdma voice traffic than gsm voice traffic in Ericsson network

    15th August 2017 at 15:09 #57275
    hungryforknowledge247
    Guest

    Hi Parsa48,
    Fast dormany is something which try and save mobiles battery consumption when link between mobile and network is idle

    15th August 2017 at 15:19 #57276
    hungryforknowledge247
    Guest

    Hi Parsa48,
    To increase traffic on 3G you can make reselection from 2G to 3G easier by changing reselection criteria. Make it reselect to 3G quicker and on lower thresholds.
    And once this is done you can make calls to be more stickier to 3G. This can be done by chaning 3G to 2G handover criteria. Hope this helps.

    5th September 2017 at 12:17 #57277
    hicham27
    Guest

    could you please help me to kown the reasons of drop (speach , HS,R99 …..)

    11th September 2017 at 08:28 #57278
    Parsa48
    Guest

    Hi dear all
    Kindly please help me about iub frame loss in Ericsson Baseband 5216 and solutions for it.

    13th September 2017 at 02:26 #57279
    Parsa48
    Guest

    Iub frame loss issues
    In one of site with Ericsson baseband 5216 node there is huge of iub frame loss. Please help me to solve it.

    8th October 2017 at 03:30 #57280
    Parsa48
    Guest

    Hi all dear friends
    I am facing with decreasing of wcdma cell availability in some Ericsson nodeb site. I, m be so happy if anyone help me to solve this issue.

  • Author
    Posts
Viewing 15 posts - 16 through 30 (of 36 total)
1 2 3
  • The forum ‘Telecom Design’ is closed to new topics and replies.