Erlang software tools...
Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

one doubt in E1

Viewing 13 posts - 1 through 13 (of 13 total)
  • Author
    Posts
  • 27th September 2006 at 06:22 #45783
    Ramajayam cyr
    Guest

    One Single E1 Mathematically can handle how many time slots of 16 Kbps traffic?

    28th September 2006 at 01:34 #45784
    heru
    Guest

    Single E1 can handle 2,048 Mbps
    traffic, so if 1 timeslot same with 16 kbps

    1E can handle 2,048Mbps / 16 Kbps = 128 Time slots

    28th September 2006 at 05:48 #45785
    Ramajayam cyr
    Guest

    Thank u heru
    Another one doubt
    “IF” Cable Length required is above 140 Meter which cable is used.

    Advanced thanks for replay

    28th September 2006 at 14:08 #45786
    ejaz
    Guest

    in E1 32 chanell are present 2 are used for sync and contorle and 30 are used fro traffic so how amny user can accomudate in 30 chanell

    2nd October 2006 at 23:32 #45787
    Bob Smith
    Guest

    read your books, standard practice

    3rd October 2006 at 01:42 #45788
    Pix
    Guest

    32 channels ? I thought it was 32 timeslots…

    1 E1 timeslot = 4 nibbles.
    1 nibble = 1 user in Full Rate / 2 users in Half Rate.

    (not taking the BTS RSL and OML into account)

    5th October 2006 at 03:06 #45789
    kulafifu
    Guest

    Hi Heru,

    I think you just mistakingly put the unit the wrong way. or perhaps you just used comma instead of dot..

    1E1 = 2.048 Mbps

    6th October 2006 at 05:17 #45790
    heru
    Guest

    ok thank’s Kulafifu

    🙂

    9th October 2006 at 11:48 #45791
    EDGE
    Guest

    if i have 2 define EDGE on one E1 with 4/4/4 config in 2206, wil it b possible??

    9th October 2006 at 12:03 #45792
    GEET MUKHRA
    Guest

    Yes you can use edge using 4/4/4 confg.

    Regards
    Geet Mukhra

    9th October 2006 at 12:04 #45793
    EDGE
    Guest

    thanx geet
    but all the TRU’s r going into noop state. suggest??

    9th October 2006 at 12:10 #45794
    GEETMUKHRA
    Guest

    Hii
    If you have defined edge on each cells BCCH then TRUs will not go in Noop.trUs will go in noop if you are using more than 12 trus on single E1.
    Can u tell me on which slots u have defined edge.
    Regards
    Geet Mukhra

    10th October 2006 at 11:02 #45795
    Ramajayam CYR
    Guest

    hi any one telme requestingly asking
    Exactly what is hop length i am searching web no answer found about hoplength all of the places calculated hope length but nobody tell what is hop length

    advanced thank for you

  • Author
    Posts
Viewing 13 posts - 1 through 13 (of 13 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.