Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

querries regarding NOKIA BTS Comm.

Viewing 15 posts - 106 through 120 (of 159 total)
1 2 3 … 7 8 9 10 11
  • Author
    Posts
  • 9th February 2007 at 05:51 #42573
    Jadee
    Guest

    Patrick – Feb 8,2007

    Thanks again for accomodating my questions.

    If no RRI for Ultrasite, how will i upgrade the Metrosite to the ultrasite?

    Metrosite is the existing BTS on site w/c has indoor coverage only. But now they want to upgrade it to Ultrasite so they could make sec1 for indoor, sec2&3 for outdoor?

    How will i connect the transmission for the existing to the Ultrasite.

    Many thanks. Hope my question aren’t annoying.. 🙂

    9th February 2007 at 13:22 #42574
    patrick
    Guest

    Jadee – 9 Feb 2007

    1st solution:
    Change all.
    The difference between Metro and ultra is physical and capacity, Bigger and wider and more TRX.

    Technology is the same. You can do 444 with ultrasite and 200 with metro.

    If no RRI, use FXC E1/T1 card. You have 4 PCM in/out.

    2nd solution:
    If you don’t destroy Metro then it will be co-localization.
    One PCM for Metro
    One PCM for Ultra
    You must declare hand-over between 2 BTS even if they were different.
    Ultra will be a new site with sector 1, 2 or 3.
    Metro stay here with only 1 sector.

    Transmission possibility:
    You can use 1 PCM for 2 BTS.
    Divised your PCM there 2.
    On your ET:
    TS 1-6 for 1st BTS
    TS 1-12 for 2nd BTS
    On your BTS (traffic manager)
    get back TS for the 1st
    get back TS for the 2nd

    10th February 2007 at 09:03 #42575
    nishant
    Guest

    hello sir,
    please give me details about E1 bypassing,what is E1?

    11th February 2007 at 06:45 #42576
    Jadee
    Guest

    Patrick – Feb 9,2007

    Hi Patrick,
    Thanks so much for answering my question.

    I will give ur suggestion a try. As of now i dont hv much questions yet regarding Nokia BTS.

    Although i have to make it a sure go because i can only have a downtime of 1hr.

    Haha.. this is such a bloody job for me..

    12th February 2007 at 15:16 #42577
    GEET MUKHRA
    Guest

    Hi,Can any one tell me Q1 pin configurations b/w ULTRA BTS and FIU(TQ and RJ 45 Connectors)??

    12th February 2007 at 15:47 #42578
    patrick
    Guest

    GEET MUKHRA – 12 Feb 2007

    Q1
    FIU is TQ connector
    BTS ULTRA connector is DB9 (PIN 1.5.9.6)

    You must cross Tx and RX.

    12th February 2007 at 15:49 #42579
    Geet Mukhra
    Guest

    Patrick
    Tell me bout RJ45 and D9…. pin configuration????

    13th February 2007 at 16:20 #42580
    Goutam Patra
    Guest

    Can u give me full concept about how E1 is created and the uses of different ports of FIU-19E in NOKIA system?

    14th February 2007 at 05:30 #42581
    Goutam Patra
    Guest

    Can u please explain me about the different cards used in NOKIA ultraside BTS

    14th February 2007 at 12:22 #42582
    patrick
    Guest

    Geet Mukhra – 12 Feb 2007

    Where do you use RJ45????

    DB9 On ULTRASITE, it is Q1.
    together
    1-6 tx or rx

    together
    5-9 tx or rx

    DB9 is above in side connector alarm ext (1-24) and Q1_sss (for nuss energy)

    15th February 2007 at 09:45 #42583
    Geet Mukhra
    Guest

    Hi patrick,,
    when u use Q1 managment for FIU19 E,then u have a RJ45 port for Q1 at FIU and DB 9 Pin port at Ultra site BTS.For that i need pin configuration for Q1 cable.
    Regards
    Geet mukhra

    16th February 2007 at 12:06 #42584
    A . Naajthina
    Guest

    shall i know about nokia bb2f and boia .and unit test
    what is the function

    17th February 2007 at 09:14 #42585
    samsul Hoque
    Guest

    what is the actual receive level in microwave transmission in GSM

    17th February 2007 at 09:48 #42586
    dewantara
    Guest

    hi sir,

    could you show me block diagram cross connection for RRI and for E1/T1?
    also the concept transmission of nokia…

    thanks

    17th February 2007 at 15:55 #42587
    patrick
    Guest

    Geet Mukhra – 15 Feb 2007

    i have an another type of FIU because i don’t have RJ45.

    On TQ or DB9, it is the same pin of PCM 2Mbit.

  • Author
    Posts
Viewing 15 posts - 106 through 120 (of 159 total)
1 2 3 … 7 8 9 10 11
  • The forum ‘Telecom Design’ is closed to new topics and replies.