Free Erlang traffic calculators

The world's first online Erlang traffic calculators

Telecom Traffic Online
  Home | Free calculators | Products | Tech. papers | Forum | About us
Erlang for Excel
A-Z termination using H.323 and SIP
A-Z termination
  • VoIP softswitch

    DUAL Softswitch is a complete Voice over IP switching and billing solution.  Flat monthly rate.

    Web control panels; Least Cost Routing; Excel tariff uploads; SIP and H323 support.

    H323 SIP softswitch >>

  • VoIP calling

    Premium quality termination for wholesale carriers with their own VoIP switch.

    44Direct >>


    Our lowest rates for wholesale carriers with their own VoIP switch.

    44Mobile >>


    Our unique online callshop billing system.

    Bill My Calls >>

AXE10 sealed devices

Wallis Dudhnath - 8th April 2019  (12:43 GMT)

Issues that I have experienced are associated with a lot errors on the E1.0 PCM system. The circuits would go into the Temporary_Out_Of_Service or Out_Of_Service state. Circuits would have to be Blocked and "restarted". In the past we would manually block circuits that had a high level of CRC errors. These circuits would then be analysed to see if the issue was Hardware (e.g. ET), Hardware, MML configuration, Software issues with the SS7 software module, etc..

VBR/ Wallis Dudhnath

andyt - 13th September 2006  (10:02 GMT)

I used to work on DX220 at the far end from AXE's. We regularly had these sealed crct problems. It seemed to be simply the method by which the crcts went down, and if someone tried to intervene manually to bring them up. If both ends didn't co-op, there were problems.

On the DX220 side, we would bring the crct's up to the nearest to working state we could, then the axe end would block, prepost, post, & deblock. (I'm not an AXE man, so if I got the terminology wrong, don't shout).



regards.

Bob Smith - 12th September 2006  (22:45 GMT)

The Reset and Maint or from C7 messeaging.

Bob Smith - 12th September 2006  (22:26 GMT)

Both ends have the same CIC value, if they do look at a X in the TX path

Are ye right there Father? - 12th September 2006  (11:01 GMT)

Any ideas what causes sealed state in devices that are operating ISUP s/w?

Have noted that the devices (when brought out of Pre-Post State) pick up a "MAINT" and "RESET" value in the LST field.

Our copy of ALEX says this is Local Admin State, and that it is Market Dependant. HELPFUL!!!!

Anyway, if I wait for the "RESET" value to clear (anywhere between 5 seconds and 20 minutes), the devices go IDLE when I BLODE. However, if I attempt to BLODE while the devices have the RESET state, they simply go sealed straight away.

Please note that the equivalent timeslots on the remote exchange can show idle while the local excha shows sealed.

Also, to add some more mystery, the RESET values do not clear in any particular order, ie they dont clear from Timeslot 1-15 then 16-31, the value clears erratically irrespective of CIC.

The problem occurs between Mobile & PSTN and internally within the Mobile nwk (both scenarios are AXE-10 each side).

Any info you can offer will be greatly appreciated! Please dont respond if your just fishing for a free course on AXE10!!!

Post a reply to this article

Name Enter your name.
Message Enter your message.
Email Optional -  If you enter your email address in this box, then you will automatically be notified if anyone replies to your message.  Your email address will only be published if you pay to post this message.
Verification
Please confirm you are human.
Press the button to post your message.
Home | Free online calculators | Products | Technical papers | Forum | Contact us | About us

Last modified: 17 May 2017

Copyright 2017. All rights reserved.