Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

SDCCH Drops

Viewing 9 posts - 1 through 9 (of 9 total)
  • Author
    Posts
  • 26th May 2010 at 14:16 #62879
    JB
    Guest

    I have been dealing with this high SDCCH drops for quite some time and need to resolve this issue. The SDCCH drops is 16.5% for the whole system and this has been going on for more than 2 years. Please help.
    My cell re-selection Hysteresis value is 6. What else can I check? Please help.

    26th May 2010 at 16:09 #62880
    PAul
    Guest

    Dear JB,

    Is the site at the border of LAC/BSC?
    If yes, then you need to try to change the re-selection Hysterisis.

    If not, just check, whether :
    1.SDCCH drops happen due to handover or not?
    2.Frequency interference-CO-channel or adjacent channel (Check BCCH only if SFH, check also TCH if BBH)

    3. THe TRX that brings SDCCH has a hardware failure.
    Try to put SDCCH to another TRX.

    BR,

    Paul

    27th May 2010 at 09:53 #62881
    xyz
    Guest

    Hi,

    U have enabled sdcch HO??
    if so try disabling it.

    if no try to remapp the sdcch in the hopping TRX to the BCCH TRX(Non hopping one).

    Also try to implement antenna hopping parameter to reduce SDCCH drop.

    Also do a cell wise analysis to arrest the hardware issues.

    Hope this will help

    Rgds
    xyx

    27th May 2010 at 10:43 #62882
    Brother
    Guest

    JB
    is it nokia?

    2nd June 2010 at 08:42 #62883
    KJB
    Guest

    SD drops.

    Kindly check the following.
    1- Site/Sector is stable means it should not be fluctuating.
    2-TRXs are stable,Not fluctuating or not being restart frequently.
    3-DL quality of the Segement/TRXs.(Q5)
    if these are degraded then replace TRXs and check VSWR should be good one.
    4- Adjust TA value (try to decrease)
    5- HYS value can be set 10 if this is Nokia BTS.

    Thanks

    31st July 2010 at 07:58 #62884
    Huawei – Man
    Guest

    Can ping-pong location update affect to increase of SDCCH Drop?

    31st July 2010 at 13:07 #62885
    Brother
    Guest

    Huawei man
    high traffic increases the drops, it is sd or tch traffic,
    one simple reason is, if there is a problem (interference,hardware or any minor problem etc.) and there is no traffic it is not visible.

    2nd August 2010 at 04:25 #62886
    jaihu
    Guest

    can adjacent channel interference cause an sd drop of 15%? in one case in our network, the cell at border and it has adjacent channel interference both and around 15% sd drop?

    2nd August 2010 at 11:50 #62887
    korgi
    Guest

    Hi All,

    I dont think that adjacent interference influence the SDCCH drops.

    to trigger the HO cell level should be (about) 5-6dbm for a while.

    adjacent frequency should be better by 15dbm to influence its adjacent frequency. Hence, they can not affect each other. I mean if one of them is better by 5dbm than other HO occurs.

    However, if this frequencies are not defined as a neighbor then they will affect each other.

    If my idea is wrong please notice me.

    BR

  • Author
    Posts
Viewing 9 posts - 1 through 9 (of 9 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.