Erlang software tools...
Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

QUEUEING PARAMETERS in NOKIA

Viewing 7 posts - 1 through 7 (of 7 total)
  • Author
    Posts
  • 26th March 2009 at 10:10 #56481
    Farkhat
    Guest

    Hi again,
    Please tell what values are suitable for QUEUEING PARAMETERS in NOKIA BSC? Or what are default values for other vendors E/// & Alcatel?
    Default values for MQL,TLC,TLH are 50%,10s,5s are seems to be much too high!

    MQL – Max Queue Length
    With this parameter you define how many call and handover attempts can be queued to wait for a TCH release in a BTS. The parameter value is a percentage (0 – 100%) of the TCHs in use in a BTS.

    TLC – Time Limit Call
    With this parameter you define the maximum queuing time for call attempts (incoming or outgoing) in the BTS in seconds. Value 0 deactivates call attempt queuing.

    TLH – Time Limit Handover
    With this parameter you define the maximum queuing time for handover attempts (both urgent and non-urgent) in the BTS in seconds.

    Thanx in advance

    26th March 2009 at 20:06 #56482
    Pix
    Guest

    I don’t understand MQL… why is it in percentage ??
    For example, how many calls can be queued if the value = 50% ?If there are 30 calls in the cell, then the nb of queued calls = 15 ?
    That’s way too much !

    10s and 5s seem acceptable. In alcatel, the default value is 6s for call attempts, but i usually recommend to increase it a little bit. In the worst case, the subscriber gets bored and hangs up by himself during the call setup 🙂

    There is no queuing for HO in alcatel, in order to give an immediate opportunity to try another neighbour cell.

    regards
    pix

    27th March 2009 at 03:37 #56483
    Farkhat
    Guest

    Thanks Pix,
    The only answear for WHY is because it’s NOKIA 🙂
    Actualy MQL is in % from TCH resource on cell. For example if there are 3 TRX on the cell, so it’s about 24 TS, so MQL will be 12.
    We changed parameters to 25%,5s,3s and SDCCH drop decreased were observed and HO sucsess rate increased!
    Next step is to make TLH=0
    Will see 😉

    9th May 2012 at 08:27 #56484
    mahdi kamalpoor
    Guest

    hi!
    in our province we have 8 Nokia_bsc, 4 BSC connected to siemens MSC and 4 other connected to NOKIA MSC
    in BSC’s connected to SIEMENS MSC queueing is active but in BSC’s connected to NOKIA msc queueing is deactive!
    Plz help me to active queueing in other BSC’s
    thank you

    24th August 2017 at 06:50 #56485
    shiv
    Guest

    what could be the value of MQL TLC and TLH

    7th September 2017 at 14:15 #56486
    Rajib Chakraborty
    Guest

    What is STRIC parameter.What is its use..

    9th September 2020 at 13:58 #74229
    hoda
    Guest

    Dear Pix
    would you please tell me what could be better value of MQL,TLC,TLH in Nokia GSM?
    many thanks

  • Author
    Posts
Viewing 7 posts - 1 through 7 (of 7 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.