Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Uplink quality poor

Viewing 11 posts - 1 through 11 (of 11 total)
  • Author
    Posts
  • 19th August 2007 at 03:58 #48890
    Ajay
    Guest

    Hi to all,
    In our network(GSM 900), we are facing lots of problem in uplink quality in one sector. Despite the Uplink quality is worst, Downlink quality is excellent. What could be the probable reason for this.
    Thanks.

    19th August 2007 at 12:06 #48891
    pix
    Guest

    have you checked the path balance of the cell ? (=low ul level and good dl level)

    i can see two possible reasons for a poor ul quality :
    1. problem in the hardware, and especially in the TRE or the combiner/duplexer
    2. ul interference coming from another cell

    you can try to isolate the cause by checking the UL quality TRX per TRX, and by changing the frequencies.

    20th August 2007 at 09:46 #48892
    Tomar
    Guest

    Hi Ajay,
    check UL Idle band Interference meas. If it is posible on each TRX.

    The 3. case could be also disturbance from other sources. We have problem on the cell, which cover jail.

    BR
    Tomar

    9th October 2007 at 16:05 #48893
    Ranjan
    Guest

    How can we check the path balance in ericsson systems?

    20th February 2012 at 08:22 #48894
    mannu
    Guest

    Dear Pix,

    I am also facing the same problem uplink quality is very bad but downlink quality is good i am working on ALU bts.

    21st February 2012 at 08:56 #48895
    mm
    Guest

    IN FOUR OF MY BSCs THE TCH BLOCKING % ARE AS UNDER –
    BSC1-9.95%
    BSC2-1.72%
    BSC3-12.57%
    BSC4-20.60%
    CAN THERE BE ANY PARTICULAR REASON AT THE BSC LEVEL FOR THIS HIGH TCH BLOCKING RATE ??
    WILL ANYONE HELP PLEASE ?
    Mr.PIX,PLEASE EXPLAIN

    7th December 2013 at 09:19 #48896
    Eng Solomon
    Guest

    In the UP link, UE Sends MSGs to Node B, which is capable of Detecting the UE for paging/Signaling puposes. However, the problem arises if hardware is Not functioning well, i.e TRXs or Combiner/Duplexer, Also check that the power is surficient enough in the system…BADICM(Cause effect) can also be one though brought by the Power incerficiency.

    I hope that will help. thanks.

    1st March 2017 at 09:46 #48897
    Yann3112
    Guest

    Uplink quality is too bad.How to fix it??

    18th March 2017 at 07:17 #48898
    LEMAURE
    Guest

    check BADICM stats and UL RXLEV distribution.
    you might be facing HW issues, interferences or coverage issues)

    29th April 2017 at 15:06 #48899
    opti_baby
    Guest

    as usual, if that is FDD system, uplink interference cause the problem, use a full band scanner to check the whole band’s floor noise (uplink), if that is a TDD system (LTE), you may use the time slot scanning funtion to scan all the symbol and RE.

    24th July 2017 at 02:28 #48900
    Parsa48
    Guest

    I have a lot uplink rx quality in 3G ran Ericsson please someone guide me to solve this problem

  • Author
    Posts
Viewing 11 posts - 1 through 11 (of 11 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.