Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

fiu 19

Viewing 15 posts - 1 through 15 (of 22 total)
1 2
  • Author
    Posts
  • 2nd February 2007 at 08:17 #46560
    Geet Mukhra
    Guest

    hi u asked u about clearence of fiu 19 for that u have to run the script tool .so that u can clear the datebase in the fiu 19

    2nd February 2007 at 15:06 #46561
    patrick
    Guest

    which database?

    The best reset is:
    setting FIU
    search button HARDWARE reset in one Tab.
    Click ON

    Your FIU reset => So, you Cut traffic.

    4th February 2007 at 08:32 #46562
    Yellaiah
    Guest

    Hi Geet & Patrick,
    Use the following steps to clear the DATA BASE FULL Alarams
    i.e.

    Run VIEW in the SCRIPT TOOL( TOOLS)
    and give following commands for NE , IDU and ODU,

    for NE 6,2,1,1, Excute it

    For IDU and ODUs K:13,1 excute it.

    regards

    Yellaiah
    yellaiah.gunti@gmail.com

    7th February 2007 at 10:26 #46563
    Geet Mukhra
    Guest

    Hi Yellaiah
    Thanx but is it traffic affecting ??

    8th February 2007 at 12:28 #46564
    Geet Mukhra
    Guest

    Can any one tell me pin configuration for Q1 managment in FIU 19 and FIU 19E….

    8th February 2007 at 16:12 #46565
    patrick
    Guest

    Q1 you can supervise FIU by BTS ultrasite or citytalk.

    ZQUS:BCF=XX; to see TRANS card (FXC ET1/T1)

    ZQWL; to see all adress Q1

    ZQWA to add adress

    You can create adress with your number BCF.

    You must make an adress on your FIU and configure in FIU setting.

    example:
    ZQUS:BCF=xx:DMR=xx;

    => you can see alarm, rssi, name, …, change setting, … on your FIU with MML.

    9th February 2007 at 12:01 #46566
    Geet Mukhra
    Guest

    Thanx patrick but i need Q1 pin configurations so that i can connect FIU and ULTRA BTS at the site through Q1 Managment……

    9th February 2007 at 13:04 #46567
    patrick
    Guest

    On Q1 BTS DB9 use pin 1, 6, 5, 9

    I don’t remember where is TX and RX but you must crusader TX and RX between Q1 DB9 ULTRA and Q1 FIU

    After, you must configure FIU Q1 with Flexihoppermanager: adress, speed, name, …

    14th February 2007 at 19:06 #46568
    RIC
    Guest

    Does anybody know why FXCRRI in XXXXHubs sometime lose CC Bank and Sync settings? Also why does Ultrasite lose TRE and only Power reset can help only Is it possible restore Hub without traffic cut

    17th February 2007 at 15:59 #46569
    patrick
    Guest

    RIC – 14 Feb 2007

    Change BOIA or FXCRRI because it is not a normal functioning.

    I have already had the same problem but i can explain why.

    This problem must be rare.

    20th February 2007 at 08:20 #46570
    RIC
    Guest

    I noticed that fault never repeat at the same XXXHub and with swapped RRI or BOI. These units after installation in other places are working enough stable.

    12th June 2010 at 05:15 #46571
    NA
    Guest

    Hi all!

    i’ve a problem using EPIU unit in FIU19E.

    so its a question, how we can use EPIU unit for making visibility of FIU to NMS (Q1 connectivity is known).

    I need full steps and configuration.

    12th June 2010 at 10:41 #46572
    KJB
    Guest

    Hi Ric & Patrrik,

    I have noticed this problem due to Faulty RRI,Some time Conteminated Pins of RRI back plan.

    Some time Hub restored after Soft RESET given to FXCRRI.

    Thx

    KJ

    13th December 2010 at 14:42 #46573
    ARUN KUMAR MISHRA
    Guest

    WHAT IS FULL FORM OF FIU .

    24th December 2010 at 17:26 #46574
    Fawad
    Guest

    What is the role of TX power.

    Why we give TX power?

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 22 total)
1 2
  • The forum ‘Telecom Design’ is closed to new topics and replies.