Free Erlang traffic calculators

The world's first online Erlang traffic calculators

Telecom Traffic Online
  Home | Free calculators | Products | Tech. papers | Forum | About us
A-Z termination - click here
A-Z termination - CLICK HERE
VoIP bandwidth calculator
  • VoIP softswitch

    DUAL Softswitch is a complete Voice over IP switching and billing solution.  Flat monthly rate.

    Web control panels; Least Cost Routing; Excel tariff uploads; SIP and H323 support.

    H323 SIP softswitch >>

  • VoIP calling

    Premium quality termination for wholesale carriers with their own VoIP switch.

    44Direct >>


    Our lowest rates for wholesale carriers with their own VoIP switch.

    44Mobile >>


    Our unique online callshop billing system.

    Bill My Calls >>

Reason of high ICM band in every site

Shahbaz - 4th April 2018  (20:24 GMT)

How we can monitor high icm band, I know how to monitor rtwp.but icm band how I can monitor?

Kalyan Borgohain - 23rd March 2017  (06:27 GMT)

ICM found high in 1800 band.Please provide the check point to resolve

Kuna - 2nd November 2016  (15:20 GMT)

ICM(idle mode Measurement) band troubleshooting..

check for Co-BCCH, adjucent-bcch, Connectors, jumper and vswr test will help to identify what is the cause of Interferences..

Dayananda - 2nd November 2016  (11:56 GMT)

Hi Devendra,,
Normally we are facing ICM band high in Combine DAS (IBS),
Reason:
1. due to connector not done in proper manor.
2.which you used accessories for DAS that accessories not meeting PIM value.
3.Fq interface in from the BTS end
4.if we have DAS connectivity in Inside the BTS room then you need to reduce the BTS room radiation.

Diffrent B/W MIMO & SISO: in single word we can say,MIMO means multi input multi output ,,,SISO single input single output

Regards,
Daya

Wd3esa - 1st November 2016  (18:00 GMT)

Hello, I faced this issue in many sites, and solved by changing feeder loss values

kumar A - 6th September 2016  (06:54 GMT)

how to resolve ICM value is high for IBS site? pls help me.

kitururu - 24th June 2016  (08:23 GMT)

High ICM band ( 2 and up) means there is interference on TCH and SD channels on Idle mode. do frequency scanning on the area to identify the cause of inter fences and check for hardware issues (jumper, connectors ) on antenna system installation

Siva - 12th May 2016  (07:26 GMT)

Kindly note ICM Band is high for IBS site (Sector 5 & 6) . Please advise how to clear.

Naef - 10th November 2015  (12:06 GMT)

Dear Gents ,
I'm facing ICM Band issue in one site & all the Hardoware connection checked , can you please advise How we can solve this issue .

ankit.singhal85@yahoo.com - 8th April 2015  (05:35 GMT)

how we define the interference band for the GSM. specify the 3GPP TS for that.

Other messages

Other messages: [Next 10 >>]

Post a reply to this article

Name Enter your name.
Message Enter your message.
Email Optional -  If you enter your email address in this box, then you will automatically be notified if anyone replies to your message.  Your email address will only be published if you pay to post this message.
Verification
Please confirm you are human.
Press the button to post your message.
Home | Free online calculators | Products | Technical papers | Forum | Contact us | About us

Last modified: 17 May 2017

Copyright 2017. All rights reserved.